3″ Rapid Z™-DRUM Replacement – Coarse
$129.95
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Coarse Grit (30/40 grit)
Related Products
Hose Assembly
No. 115. Hose assembly for Seam Phantom® & Sink BULL™
Sold as a complete 6′ assembly with a brass threaded male fitting to attach to the valve and a brass female garden hose fitting on the opposite end. All hose assemblies will be supplied with a straight fitting to attach to the valve instead of the old 45 degree fitting.
For use on all Electric Seam Phantoms® that require external water feed plus the Sink BULL™.
3″ Rapid Z™-DRUM Replacement Bearing
No. 230, Replacement Bearing for 3″ Rapid ZTM-DRUM
Rapid Z™-CUT Blade Spacer
No. 111, Blade spacer, Sold Individually
This is the spacer between the blades on a Rapid Z™-CUT
13 required for the Rapid Z™-CUT with top bearing
17 required for the Rapid Z™-CUT NO bearing
Sink BULL™ – Replacement Grips
Replacement Grip Sets for all Sink BULLs™. These will replace the older, bicycle style, grip on the ORIGINAL Sink BULL as well as the newer Sink BULL™ LT.
- USA made grip
- Sold as a pair complete with hardware
- Longer Screw for Original Sink BULL
- Shorter Screw for Sink BULL LT
3″ Rapid Z™-DRUM – Fine
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
Screws
No. 1, Screws (#10 x 1/2″ Stainless Button Head Screws)
Sold in a pack of 10 screws
Multiple uses:
- Attaches the white rub plate and valve bracket on the original Seam Phantom®.
- Attaches the white rub plates, valve bracket and spray shield on Seam Phantom® 2.0
- Attaches the white rub plate, brackets and P-clips on the Original Sink BULL™
- Buy multiple packs if you require more than 10 screws.
- Does NOT fit Sink BULL™ LT
No. 310, Screws (#10 x 3/8″ Stainless Button Head Screws)
Sold in a pack of 10 screws
- Attaches the white rub plate, brackets and P-clips on the Sink BULL™ LT
- Buy multiple packs if you require more than 10 screws.
- Does NOT fit the Original Sink BULL™ or Seam Phantom Models
3″ Rapid Z™-DRUM Cap
No. 203, Cap for Rapid ZTM-DRUM
Retains the diamond drum on the Rapid ZTM-DRUM
1″ Rapid Z™-DRUM – Fine
A 1″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. This is the bit you need to clean out the tight corner radius on square sinks. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the extra material left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Fine Grit (120/150 grit)