3″ Rapid Z™-DRUM – Coarse
$289.95 (MSRP) AVAILABLE THROUGH A STOCKING DISTRIBUTOR ONLY.
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
Related Products
Rapid Z™-CUT Bearing Press
No. 401, Bearing press
This is the press used to install the bearing in the Rapid Z™-CUT bearing replacement video. We offer it here as a convenience.
Click Here to Watch Our Rapid Z™ Bearing Replacement Video!
3″ Rapid Z™-DRUM Arbor Key
No. 240, Key for 3″ Rapid ZTM-DRUM
Replacement key for the Rapid ZTM-DRUM
3″ Rapid Z™-DRUM Cap
No. 203, Cap for Rapid ZTM-DRUM
Retains the diamond drum on the Rapid ZTM-DRUM
1″ Rapid Z™-DRUM – Fine
$139.95 (MSRP) AVAILABLE THROUGH A STOCKING DISTRIBUTOR ONLY.
A 1″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. This is the bit you need to clean out the tight corner radius on square sinks. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the extra material left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Fine Grit (120/150 grit)
3″ Rapid Z™-CUT Outer Ring
No. 107, Outer bearing ring
Large outer ring used on the Rapid Z™-CUT with new blades
Multi-Function Wrench – Sink BULL LT
This Multi-Function Wrench is designed for use with The Sink BULL™LT. The Wrench fits all 3″ and 1″ Rapid-Z Abrasives. It is also used as a gauge block to set the initial grinding height on the Sink BULL™LT.
Sink BULL™ Height Adjustment Handle Only
Replacement Sink BULL™ height adjustment handle.
- Fits all Sink BULLs
1″ Rapid Z™-DRUM – Coarse
$139.95 (MSRP) AVAILABLE THROUGH A STOCKING DISTRIBUTOR ONLY.
A 1″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. This is the bit you need to clean out the tight corner radius on square sinks. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the extra material left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit (30/40 grit)