3″ Rapid Z™-DRUM Replacement – Coarse
$144.95
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Coarse Grit (30/40 grit)
Related Products
3″ Rapid Z™-DRUM Replacement – Fine
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Fine Grit (120/150 grit)
3″ Rapid Z™-CUT Inner Ring
No 105, Inner bearing ring
Inner ring that is pressed onto the template follower bearing on a Rapid Z™-CUT
Bearing sold separately
Rapid Z™-CUT Bearing Press
No. 401, Bearing press
This is the press used to install the bearing in the Rapid Z™-CUT bearing replacement video. We offer it here as a convenience.
Click Here to Watch Our Rapid Z™ Bearing Replacement Video!
1″ Rapid Z™-DRUM – Coarse
A 1″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. This is the bit you need to clean out the tight corner radius on square sinks. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the extra material left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit (30/40 grit)
3″ Rapid Z™-DRUM Cap
No. 203, Cap for Rapid ZTM-DRUM
Retains the diamond drum on the Rapid ZTM-DRUM
Rapid Z™-CUT Screws
No. 23, Screws for bearing ring
Sold in a pack of (4) #23 screws
Replacement screws used to attach the large outer bearing ring on a Rapid Z™-CUT
Screws
No. 1, Screws (#10 x 1/2″ Stainless Button Head Screws)
Sold in a pack of 10 screws
Multiple uses:
- Attaches the white rub plate and valve bracket on the original Seam Phantom®.
- Attaches the white rub plates, valve bracket and spray shield on Seam Phantom® 2.0
- Attaches the white rub plate, brackets and P-clips on the Original Sink BULL™
- Buy multiple packs if you require more than 10 screws.
- Does NOT fit Sink BULL™ LT
No. 310, Screws (#10 x 3/8″ Stainless Button Head Screws)
Sold in a pack of 10 screws
- Attaches the white rub plate, brackets and P-clips on the Sink BULL™ LT
- Buy multiple packs if you require more than 10 screws.
- Does NOT fit the Original Sink BULL™ or Seam Phantom Models
3″ Rapid Z™-CUT without Bearing
The Rapid Z™-CUT without a bearing is used for fast free-hand shaping or can be adapted for CNC use. The blades can be rearranged to minimize “apple coring” and they can be replaced easily. It’s also center water feed compatible.
- Fits 5/8-11 arbor threads (M14 version available)
- Center water feed
- Maximum RPM 12,000
- Uses 17 replacement blades
Click Here to Watch Our Sink BULL™ & Rapid Z™ Video!