Wheel Axle Assembly
NO LONGER AVAILABLE
NO. 15, 17, 18. Sold as a kit with (1) #15 wheel axles, (1) #17 bearing shims, and (1) #18 lock nuts.
Related Products
Glide Guide, 72″
72″ Glide Guide Rail for use with the ORIGINAL Seam Phantom. Can be used to produce seams up to 66″ long. This was our preferred guide rail design for over a decade. Also available in 48″ and 92″
*Note: Does not work with Seam Phantom 2.0
*Note: This item is considered “oversize” by FedEx. The shipping cost will include additional fees for “oversize” and handling.
Updated Wheel Axle Assembly
Updated version of the GWAF.
Sold as a kit (1) #215 Brass Axle, (1) #17 Bearing Shim, (1) #216 Screw, and (1) #217 Washer.
Two Axle assemblies required per Seam Phantom
Universal Replacement for ALL Seam Phantoms.
SL3® 3 Inch Rigid Turbo Abrasive, 60 Grit
3″, rigid backed, turbo abrasive
- 60 grit – Popular replacement turbo for the Seam Phantom®
- Wet use only
- 3 1/8″ actual outside diameter
- Locks into the SL3® Snail Lock Adapter
- Maximum RPM 4000
Set Screws
NO. 19. Sold in a pack of 2.
Set Screws for the original black valve bracket used on the original electric Seam Phantoms®
Not for use on Seam Phantom 2.0
Hose Assembly
No. 115. Hose assembly for Seam Phantom® & Sink BULL™
Sold as a complete 6′ assembly with a brass threaded male fitting to attach to the valve and a brass female garden hose fitting on the opposite end. All hose assemblies will be supplied with a straight fitting to attach to the valve instead of the old 45 degree fitting.
For use on all Electric Seam Phantoms® that require external water feed plus the Sink BULL™.
Arbor Spacer
Arbor Spacer for use with all Electric Seam Phantoms®. Installed between the red snail lock adapter and the grinder to locate the turbo at the most useful position. Works with 5/8-11 or M14 threads.
- 0.19″ thick for all original Seam Phantoms® and most Seam Phantom® 2.0 versions
- 0.32″ thick for Seam Phantom® 2.0 with Metabo grinder ONLY
Placard Kit
No. 32 & No. 33, Safety Placard Kit
Sold as a kit with (1) #32 Eye Protection placard and (1) #33 GFCI Protection placard
Universal replacement for all Seam Phantoms and Sink BULL.
Screws
No. 1, Screws (#10 x 1/2″ Stainless Button Head Screws)
Sold in a pack of 10 screws
Multiple uses:
- Attaches the white rub plate and valve bracket on the original Seam Phantom®.
- Attaches the white rub plates, valve bracket and spray shield on Seam Phantom® 2.0
- Attaches the white rub plate, brackets and P-clips on the Original Sink BULL™
- Buy multiple packs if you require more than 10 screws.
- Does NOT fit Sink BULL™ LT
No. 310, Screws (#10 x 3/8″ Stainless Button Head Screws)
Sold in a pack of 10 screws
- Attaches the white rub plate, brackets and P-clips on the Sink BULL™ LT
- Buy multiple packs if you require more than 10 screws.
- Does NOT fit the Original Sink BULL™ or Seam Phantom Models