3″ Rapid Z™-CUT Replacement Blades
$9.95
Replacement blade for the Rapid Z™-CUT. Watch our video below on how to change the blades.
- 3″ diameter x .08 thick x 7/8 arbor hole
- Maximum RPM 12,000
- Price listed is for one blade
- Rapid Z™-CUT WITH TEMPLATE BEARING uses 12 replacement blades
- Rapid Z™-CUT NO BEARING uses 17 replacement blades
Click Here to Watch Our Rapid Z™ Blade Replacement Video!
Related Products
Screws
No. 1, Screws (#10 x 1/2″ Stainless Button Head Screws)
Sold in a pack of 10 screws
Multiple uses:
- Attaches the white rub plate and valve bracket on the original Seam Phantom®.
- Attaches the white rub plates, valve bracket and spray shield on Seam Phantom® 2.0
- Attaches the white rub plate, brackets and P-clips on the Original Sink BULL™
- Buy multiple packs if you require more than 10 screws.
- Does NOT fit Sink BULL™ LT
No. 310, Screws (#10 x 3/8″ Stainless Button Head Screws)
Sold in a pack of 10 screws
- Attaches the white rub plate, brackets and P-clips on the Sink BULL™ LT
- Buy multiple packs if you require more than 10 screws.
- Does NOT fit the Original Sink BULL™ or Seam Phantom Models
Sink BULL™ – Replacement Grips
Replacement Grip Sets for all Sink BULLs™. These will replace the older, bicycle style, grip on the ORIGINAL Sink BULL as well as the newer Sink BULL™ LT.
- USA made grip
- Sold as a pair complete with hardware
- Longer Screw for Original Sink BULL
- Shorter Screw for Sink BULL LT
3″ Rapid Z™-CUT with Top Bearing
The Rapid Z™-CUT is a 3″ diameter, stacked blade type Z Wheel, specifically designed for use with the Sink BULL™ to shape sink cutouts. It comes with a bearing and ring system designed to ride along a template and help compensate for blade wear. It excels at grinding away stone /quartz quickly but will always leave a small amount to be cleaned up with a drum wheel as the final step. The blades can be rearranged to minimize “apple coring” and they can be replaced easily. It’s center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Center water feed
- Maximum RPM 12,000
- Uses 12 replacement blades
Click Here to Watch Our Sink BULL™ & Rapid Z™ Video!
3″ Rapid Z™-DRUM Replacement – Coarse
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Coarse Grit (30/40 grit)
Multi-Function Wrench – Sink BULL LT
This Multi-Function Wrench is designed for use with The Sink BULL™LT. The Wrench fits all 3″ and 1″ Rapid-Z Abrasives. It is also used as a gauge block to set the initial grinding height on the Sink BULL™LT.
3″ Rapid Z™-DRUM – Fine
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
Rapid Z™-CUT Blade Spacer
No. 111, Blade spacer, Sold Individually
This is the spacer between the blades on a Rapid Z™-CUT
13 required for the Rapid Z™-CUT with top bearing
17 required for the Rapid Z™-CUT NO bearing
3″ Rapid Z™-DRUM Replacement – Fine
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Fine Grit (120/150 grit)