3″ Rapid Z™-DRUM Replacement – Fine
$129.95 (MSRP) AVAILABLE THROUGH A STOCKING DISTRIBUTOR ONLY.
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Fine Grit (120/150 grit)
Related Products
3″ Rapid Z™-CUT Outer Ring
No. 107, Outer bearing ring
Large outer ring used on the Rapid Z™-CUT with new blades
3″ Rapid Z™-DRUM – Coarse
$289.95 (MSRP) AVAILABLE THROUGH A STOCKING DISTRIBUTOR ONLY.
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
Rapid Z™-CUT Blade Spacer
No. 111, Blade spacer, Sold Individually
This is the spacer between the blades on a Rapid Z™-CUT
13 required for the Rapid Z™-CUT with top bearing
17 required for the Rapid Z™-CUT NO bearing
3″ Rapid Z™-DRUM Arbor Key
No. 240, Key for 3″ Rapid ZTM-DRUM
Replacement key for the Rapid ZTM-DRUM
Sink BULL™ Height Adjustment Handle Kit
Replacement Sink BULL™ height adjustment handle includes bolt and washer.
- Fits all Sink BULLs
- Sold as a kit
1″ Rapid Z™-DRUM – Coarse
$139.95 (MSRP) AVAILABLE THROUGH A STOCKING DISTRIBUTOR ONLY.
A 1″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. This is the bit you need to clean out the tight corner radius on square sinks. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the extra material left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit (30/40 grit)
3″ Rapid Z™-CUT Inner Ring
No 105, Inner bearing ring
Inner ring that is pressed onto the template follower bearing on a Rapid Z™-CUT
Sink BULL™ – UPGRADED Replacement Grips
Tired of your Sink BULL™ grips sliding around on the bar? We were too!!! After trying every type of grip adhesive we could find, we just sourced better grips. We’ve been using them for a couple years and our fabricators love them. These upgraded replacement grips have the extra screw length required to fit the original Sink BULL™.
- Sold as a pair
- Fits the Original Sink BULL™
- Does NOT fit the New Sink BULL™LT