3" Rapid Z™-CUT Inner Ring 
3″ Rapid Z™-DRUM Replacement – Coarse
$129.95
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Coarse Grit (30/40 grit)
Related Products
1″ Rapid Z™-DRUM – Fine
A 1″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. This is the bit you need to clean out the tight corner radius on square sinks. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the extra material left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Fine Grit (120/150 grit)
3″ Rapid Z™-DRUM – Fine
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
3″ Rapid Z™-CUT Outer Ring
No. 107, Outer bearing ring
Large outer ring used on the Rapid Z™-CUT with new blades
Rapid Z-CUT Screws Sold Separately.
3″ Rapid Z™-DRUM – Coarse
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
3″ Rapid Z™-CUT Inner Ring
No 105, Inner bearing ring
Inner ring that is pressed onto the template follower bearing on a Rapid Z™-CUT
Bearing sold separately
3″ Rapid Z™-DRUM Replacement – Fine
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Fine Grit (120/150 grit)
3″ Rapid Z™-DRUM Cap
No. 203, Cap for Rapid ZTM-DRUM
Retains the diamond drum on the Rapid ZTM-DRUM
3″ Rapid Z™-DRUM Replacement Bearing
No. 230, Replacement Bearing for 3″ Rapid ZTM-DRUM