Rapid Z™-CUT Bearing Press 
3″ Rapid Z™-CUT Replacement Blades
$9.45
Replacement blade for the Rapid Z™-CUT. Watch our video below on how to change the blades.
- 3″ diameter x .08 thick x 7/8 arbor hole
- Maximum RPM 12,000
- Price listed is for one blade
- Rapid Z™-CUT WITH TEMPLATE BEARING uses 12 replacement blades
- Rapid Z™-CUT NO BEARING uses 17 replacement blades
Click Here to Watch Our Rapid Z™ Blade Replacement Video!
Related Products
3″ Rapid Z™-DRUM – Coarse
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
Rapid Z™-CUT Bearing Press
No. 401, Bearing press
This is the press used to install the bearing in the Rapid Z™-CUT bearing replacement video. We offer it here as a convenience.
Click Here to Watch Our Rapid Z™ Bearing Replacement Video!
Rapid Z™-CUT Cap
No. 103, Cap for Rapid Z™-CUT
Retains the blades on the Rapid Z™-CUT. Works on Rapid Z™-CUT with and without a template follower bearing
1″ Rapid Z™-DRUM – Coarse
A 1″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. This is the bit you need to clean out the tight corner radius on square sinks. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the extra material left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit (30/40 grit)
White Rub Plate – Original Sink BULL™
This is a replacement white plastic rub plate for the lower surface of the original Sink BULL™. This kit includes 6 extra attachment screws.
- Fits the original Sink BULL™
- Does NOT fit the New Sink BULL™LT
3″ Rapid Z™-DRUM Cap
No. 203, Cap for Rapid ZTM-DRUM
Retains the diamond drum on the Rapid ZTM-DRUM
3″ Rapid Z™-DRUM – Fine
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
Sink BULL™ Height Adjustment Handle Kit
Replacement Sink BULL™ height adjustment handle includes bolt and washer.
- Universal replacement for Sink BULL and Sink BULL LT
- Sold as a kit