1" Rapid Z™-DRUM - Coarse 
3″ Rapid Z™-CUT Replacement Blades
$9.45
Replacement blade for the Rapid Z™-CUT. Watch our video below on how to change the blades.
- 3″ diameter x .08 thick x 7/8 arbor hole
- Maximum RPM 12,000
- Price listed is for one blade
- Rapid Z™-CUT WITH TEMPLATE BEARING uses 12 replacement blades
- Rapid Z™-CUT NO BEARING uses 17 replacement blades
Click Here to Watch Our Rapid Z™ Blade Replacement Video!
Related Products
3″ Rapid Z™-CUT Outer Ring
No. 107, Outer bearing ring
Large outer ring used on the Rapid Z™-CUT with new blades
Rapid Z-CUT Screws Sold Separately.
1″ Rapid Z™-DRUM – Fine
A 1″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. This is the bit you need to clean out the tight corner radius on square sinks. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the extra material left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Fine Grit (120/150 grit)
3″ Rapid Z™-CUT Replacement Bearing
No. 24, Bearing for Rapid Z™-CUT
Replacement bearing for the Rapid Z™-CUT with template follower
Click Here to Watch Our Rapid Z™ Bearing Replacement Video!
3″ Rapid Z™-DRUM Cap
No. 203, Cap for Rapid ZTM-DRUM
Retains the diamond drum on the Rapid ZTM-DRUM
Sink BULL™ – UPGRADED Replacement Grips
Tired of your Sink BULL™ grips sliding around on the bar? We were too!!! After trying every type of grip adhesive we could find, we just sourced better grips. We’ve been using them for a couple years and our fabricators love them. These upgraded replacement grips have the extra screw length required to fit the original Sink BULL™.
- Sold as a pair
- Fits the Original Sink BULL™
- Does NOT fit the New Sink BULL™LT
3″ Rapid Z™-DRUM – Coarse
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
NEW White Rub Plate Nose – Sink BULL LT
This is a replacement white plastic rub plate for the lower surface of the Sink BULL™LT – THIS IS THE NOSE PORTION ONLY. This kit includes 8 extra attachment screws.
- Fits the NEW Sink BULL™LT
- Does NOT fit the original Sink BULL™
Rapid Z™-CUT Cap
No. 103, Cap for Rapid Z™-CUT
Retains the blades on the Rapid Z™-CUT. Works on Rapid Z™-CUT with and without a template follower bearing