Showing 101–111 of 111 resultsSorted by popularity
Sink BULL™ – UPGRADED Replacement Grips
Tired of your Sink BULL™ grips sliding around on the bar? We were too!!! After trying every type of grip adhesive we could find, we just sourced better grips. We’ve been using them for a couple years and our fabricators love them. These upgraded replacement grips have the extra screw length required to fit the original Sink BULL™.
- Sold as a pair
- Fits the Original Sink BULL™
- Does NOT fit the New Sink BULL™LT
NSI Radius Templates – 2 Piece Set
We’ve been making and using these templates in our shop for the past few years, and have found them to be an essential tool for the fabricator. Use these templates to mark out accurate radii for hand fabrication or to show customers what a certain radius will look like. The radii are slightly undersized to fit a Presto™ white out pen so the center of the line line will be true to size.
Combined Total of 12 Different Corner Radii
Presto pen not included
Colors will vary
Set includes:
(1) Radius Template 1
(1) Radius Template 2
Sink BULL™ Height Adjustment Handle Only
Replacement Sink BULL™ height adjustment handle.
- Universal replacement for Sink BULL and Sink BULL LT
4″ Redeemer Resin Abrasive, 200 Grit
4″ Flexible Resin diamond abrasive with hook & loop attachment
- 200 Grit
- 3.9″ actual outside diameter
- Color-coded gray
- Perfect for top polishing natural granite and quartzite
- This is the same type of resin pad we supply in our Top Polish Kit
- Requires less down pressure than other resin pads used for top polishing
- Will create a polish with exceptional clarity at low speeds or high speeds
- Always use plenty of water – never run dry
- Drive it with a True 4″ Rigid Hook and Loop backer when top polishing
4″ Redeemer Resin Abrasive, 500 Grit
4″ Flexible Resin diamond abrasive with hook & loop attachment
- 500 Grit
- 3.9″ actual outside diameter
- Color-coded blue
- Perfect for top polishing natural granite and quartzite
- This is the same type of resin pad we supply in our Top Polish Kit
- Requires less down pressure than other resin pads used for top polishing
- Will create a polish with exceptional clarity at low speeds or high speeds
- Always use plenty of water – never run dry
- Drive it with a True 4″ Rigid Hook and Loop backer when top polishing
SL3® 7″ FOAM Hook and Loop Backer (6.8″ actual diameter)
7″ hook and loop backer with FOAM padding (6.8″ actual diameter)
- Locks into the SL3® Snail Lock Adapter
- Designed with a “hook” face for use with hook & loop style abrasives
- Machined flat for smooth running
- 1/4″ of semi-soft foam padding under the “hook” to provide cushion
- Designed specifically for quartz restoration specialists
3″ Rapid Z™-DRUM Replacement – Coarse
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Coarse Grit (30/40 grit)
3″ Rapid Z™-DRUM Replacement – Fine
Replacement drum for the 3″ Rapid Z™-DRUM. Vacuum brazed diamond abrasive can be flipped on the arbor to gain extra life.
- Maximum RPM 8500
- Reversible
- Fine Grit (120/150 grit)
3″ Rapid Z™-DRUM – Fine
A 3″ diameter vacuum brazed drum wheel, specifically designed for use with the Sink BULL™. Available in two grits with a top bearing to ride along the template. The coarse grit cleans up the rough surface left by the Rapid Z™-CUT and the fine grit further smooths the surface leaving it ready to polish. This is the only vacuum brazed drum wheel with reversible and replaceable drums. The height matches the Rapid Z™-CUT so height adjustments on the Sink BULL are not required between bits. It is center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Reversible, and replaceable diamond abrasive drum
- Height matched to the Rapid Z™-CUT
- Center water feed compatible
- Maximum RPM 8500
- Coarse grit = approximately 30/40 grit
- Fine Grit = approximately 120/150 grit
3″ Rapid Z™-CUT without Bearing
The Rapid Z™-CUT without a bearing is used for fast free-hand shaping or can be adapted for CNC use. The blades can be rearranged to minimize “apple coring” and they can be replaced easily. It’s also center water feed compatible.
- Fits 5/8-11 arbor threads (M14 version available)
- Center water feed
- Maximum RPM 12,000
- Uses 17 replacement blades
Click Here to Watch Our Sink BULL™ & Rapid Z™ Video!
3″ Rapid Z™-CUT with Top Bearing
The Rapid Z™-CUT is a 3″ diameter, stacked blade type Z Wheel, specifically designed for use with the Sink BULL™ to shape sink cutouts. It comes with a bearing and ring system designed to ride along a template and help compensate for blade wear. It excels at grinding away stone /quartz quickly but will always leave a small amount to be cleaned up with a drum wheel as the final step. The blades can be rearranged to minimize “apple coring” and they can be replaced easily. It’s center water feed compatible (note: the Sink BULL™ does not use center water feed).
- Fits 5/8-11 arbor threads (M14 version available)
- Center water feed
- Maximum RPM 12,000
- Uses 12 replacement blades
Click Here to Watch Our Sink BULL™ & Rapid Z™ Video!